Product Code: MCM1201TINT
Chemical Name/Class: ALKYD ENAMEL CAS Number:
-------------------------------------------------------------------------------
SECTION IIA: HAZARDOUS INGREDIENTS
(To Nearest .10%) Vapor
Ingredient CAS Number % by Wt. % by Vol. LEL Press.
1. MINERAL SPIRITS 8052-41-3 30.20 44.70 .7 4.60
2. VM&P 64742-89-8 4.90 7.60 1.0 26.00
NA = Not Applicable; NE = Not Established
-------------------------------------------------------------------------------
SECTION IIB: OCCUPATIONAL EXPOSURE LIMITS
----OSHA PEL's------ -------------------ACGIH TLV's----------

.
.
.
.
.
.
.
.
.
.
.
NA = Not Applicable; NE = Not Established
-------------------------------------------------------------------------------
SECTION III: PHYSICAL DATA
Boiling Range (degrees F): 247 - 393 Pounds per Gallon: 9.61
Vapor Density: HEAVIER THAN AIR Evaporation Rate: SLOWER THAN ETHER
Solubility in Water: NA

Volatiles (%) by Weight by Volume
Total 35.1 52.3
Exempt VOC 0 0
Non-exempt 35.1 52.3

VOC wt/gal: 3.37 lbs non-exempt solvent per adjusted gallon
Appearance: OPAQUE LIQUID

-------------------------------------------------------------------------------
MCM PAINTS Page 1
MCM1201TINT Revision Date: 11/18/99
MATERIAL SAFETY DATA SHEET
MCM1201TINT Printed: 05/10/04 Revised: 11/18/99 Page 2
===============================================================================
-------------------------------------------------------------------------------
SECTION IV: FIRE AND EXPLOSION HAZARD DATA
Flammability Classification:
OSHA: COMBUSTIBLE DOT: CLASS 3 (FLAMMABLE LIQUIDS)
Flash Point: 550000 (Method: Tcc)
UEL: 6

Extinguishing Media: CO2

Unusual Fire and Explosion Hazards
Containers exposed to intense heat from fires should be cooled with water
to prevent vapor pressure buildup which could result in container rupture.
Container areas exposed to direct flame contact should be cooled with
large quantities of water as needed to prevent weakening of container
structure.

Special Firefighting Procedures
CAUTION: COMBUSTIBLE. Do not enter confined fire space without full
bunker gear (Helmet with face shield, bunker coats, gloves and rubber boots.
Including a positive pressure NIOSH approved self-contained breathing
apparatus. Cool fire exposed containers with water.
-------------------------------------------------------------------------------
SECTION V: HEALTH HAZARD DATA
Effects of Overexposure
EYE Contact: Liquid is minimally irritating to the eyes. High vapor
concentractions may cause irritation.
SKIN CONTACT: Liquid is slightly irritating to the skin. Prolonged or repeated
contact can result in defatting and drying of the skin which may result in
skin irritation and dermatitis.
INHALATION: Vapors may be irritating to nose, throat and respiratory tract.
High vapor concentrations may cause CNS depression.

Medical Conditions Prone to Aggravation by Exposure
Pre-existing eye, skin and respiratory disorders may be aggravated by
exposure to this product.

Primary Routes of Entry into the Body, and Effects
Eyes, Skin, Lungs

EMERGENCY FIRST-AID PROCEDURES
EYE CONTACT: Flush eyes with plenty of water for 15 minutes while holding
eyelids open. Get medical attention.
Skin Contact: Remove contaminated clothing/shoes. Flush skin with water.
Follow by washing with soap and water. if irritation occurs, get mecical
attention. Do not reuse clothing until cleaned.
Inhalation: Remove victim to fresh air and provide oxygen if breathing
is difficult. Give artificial respiration if not breathing. Get medical
attention.
INGESTION: Do not induce vomiting. If vomiting occurs spontaneously, keep
head below hips to prevent aspiration of liquid into the lungs. Get medical
attention.
NOTE TO PHYSICIANS: if more than 2.0 ml per kg has been ingested and vomiting
has not occured, emesis should be induced with supervision.Keep victim's
head below hips to prevent aspiration. If symptoms such as loss of gag
reflex, convulsions or unconsciousness occur before emesis, gastric lavage
using a cuffed endotracheal tube shoul be considered.

-------------------------------------------------------------------------------
MCM PAINTS Page 2
MCM1201TINT Revision Date: 11/18/99
MATERIAL SAFETY DATA SHEET
MCM1201TINT Printed: 05/10/04 Revised: 11/18/99 Page 3
===============================================================================
-------------------------------------------------------------------------------
SECTION VI: REACTIVITY DATA

Stability: STABLE Hazardous Polymerization WILL NOT OCCUR.

Hazardous Decomposition Products
Carbon Monoxide and unidentified organic compounds may be formed
during combustion.

Conditions to Avoid
Avoid heat, flame and contact with strong oxidizing agents.

Incompatibilities (Materials to Avoid)
Strong oxidizing agents.
-------------------------------------------------------------------------------
SECTION VII: SPILL OR LEAK PROCEDURES; WASTE DISPOSAL
Steps to be taken if Material is Leaked or Spilled
CAUTION: combustible.***Large Spills*** Eliminate potential sources of
ignigtion. Wear appropriate respirator and other protective clothing. Shut
off source of leak only if safe to do so. Dike and contain. REmove with
vacuum trucks or pump to storage/salvage vessels. Soak up residue with an
abosrbent such as clay, sand or other suitable material. Place in
non-leaking containers and seal tightly for proper disposal. Flush area
with water to remove trace residue. Dispose of flush solution as above.
***Small Spills*** Take up with an absorbent material and place in
non-leaking containers for proper disposal.

Waste Disposal Methods
Under EPA - RCRA (40 CFR 261.21) if this product becomes a waste material
it would be an ignitable hazardous waste (D001) Refer to latest EPA or state
regulations regarding proper disposal.
-------------------------------------------------------------------------------
SECTION VIII: SAFE HANDLING AND USE INFORMATION
Respiratory Protection
Avoid prolonged or repeated breathing of vapors.
If exposure may or does exceed occupational exposure
limits use a NIOSH-approved respirator to prevent
overexposure. In accord with 29CFR 1910.134 use
either an atmosphere-supplying respirator or an
air-purifying respirator for organic vapors.

Ventilation
Provide sufficient mechanical (general, or local exhaust)
ventilation to maintain exposure below TLV(S)

Protective Gloves
Avoid contact with skin. Wear chemical-resistant gloves.

Eye Protection
Avoid contact with eyes. Wear safety glasses or goggles.

Other Protective Equipment
Wear chemical resistant clothing.

-------------------------------------------------------------------------------
MCM PAINTS Page 3
MCM1201TINT Revision Date: 11/18/99
MATERIAL SAFETY DATA SHEET
MCM1201TINT Printed: 05/10/04 Revised: 11/18/99 Page 4
===============================================================================
Hygienic Practices
WASH WITH SOAP AND WATER BEFORE EATING, DRINKING
SMOKING, APPLYING COSMETICS, OR USING TOILET FACILITIES.
LAUNDER CONTAMINATED CLOTHING BEFORE REUSE. AIR-DRY
CONTAMINATED CLOTHING IN A WELL VENTILATED AREA
BEFORE LAUNDERING.
-------------------------------------------------------------------------------
SECTION IX: SPECIAL PRECAUTIONS
Handling and Storing
Store in a cool, dry area away from heat, sparks and flame. cONTAINERS
EVEN THOSE THAT HAVE BEEN EMPTIED, CAN CONTAIN EXPLOSIVE VAPORS. dO NOT
CUT, DRILL, GRIND, WELD OR PERFORM SIMILAR OPERATIONS ON OR NEAR CONTAINERS
TO EMPTY THEM. sTATIC ELECTRICITY MAY ACCUMULATE AND CREATE A FIRE HAZARD
GROUND FIXED EQUIPMENT. bOND AND GROUND TRANSFER CONTAINERS AND EQUIPMENT.

Other Precautions
Wash with soap and water before eating, drinking, smoking, applying
COSMETICS, OR USING TOILET FACILITIES. lAUNDER CONTAMINATED CLOTHING BEFORE
REUSE. aIR-DRY CONTAMINATED CLOTHING IN A WELL VENTILATED AREA BEFORE
LAUNDERING.
===============================================================================
END OF MSDS
===============================================================================

-------------------------------------------------------------------------------
MCM PAINTS Page 4
MCM1201TINT Revision Date: 11/18/99